Flight Manager

Preflight checklist sessions for your drone fleet

Available Drones

4

In Progress

3

Completed

266

Drone 003 - 糖糖

Checklist completeFull Preflight

Started Sep 3, 2026, 5:25 PM

Session Timer

00:00:00

Checklist Progress20/20

Last Completed Step

Record charger voltage

5:39:56 PM

Save Status

All changes synced

Updated Sep 3, 2026, 5:39 PM

Battery Check

Complete each item in sequence.

Step 1Completed 5:25:41 PM

Measure and record battery voltage

  • Record the battery number and the measured battery voltage.

Acceptable range: VMeasured > 49.6

Battery voltage is within the acceptable range.

Battery Placement

Complete each item in sequence.

Step 2Completed 5:30:22 PM

Align the battery to the white line

Step 3Completed 5:30:23 PM

Secure the velcro straps

Step 4Completed 5:30:24 PM

Wiggle-test the battery

The battery should not move once strapped in.

Battery Cover

Complete each item in sequence.

Step 5Completed 5:30:26 PM

Tape down the battery cover with flight tape

Remote ID

Complete each item in sequence.

Step 6Completed 5:30:34 PM

Turn on the Remote ID module

Flip the red switch on the Remote ID module to power it on.

Hardware Check

Complete each item in sequence.

Step 7Completed 5:30:36 PM

Verify the VTOL motor does not budge

Grab the VTOL motor with your palm and lightly try shifting it.

Step 8Completed 5:30:36 PM

Inspect propellers for cracks or cuts

Step 9Completed 5:30:38 PM

Inspect the servo and rod for secure attachment

Step 10Completed 5:30:39 PM

Manually move the rudder to confirm servo engagement

Ground Control Center & Drone Connectivity

Complete each item in sequence.

Step 11Completed 5:30:40 PM

Confirm airspeed sensor data in MissionPlanner

Blow on the airspeed sensor and verify the reading is reflected in MissionPlanner.

Remote Controlled Pre-Check

Complete each item in sequence.

Step 12Completed 5:30:41 PM

Run the same-direction rudder test

Flip the red button toward the pilot to enter airplane mode, then use the left joystick so both rudders move in the same direction.

  • Repeat the motion 10x.
  • Observe rudder smoothness and speed on every pass.
Step 13Completed 5:30:49 PM

Listen for unusual sounds during the same-direction test

Step 14Completed 5:30:50 PM

Run the opposite-direction rudder test

Use the right joystick so the rudders move in opposite directions.

  • Repeat the motion 10x.
  • Observe rudder smoothness and speed on every pass.
Step 15Completed 5:30:52 PM

Listen for unusual sounds during the opposite-direction test

MissionPlanner Connectivity Check

Complete each item in sequence.

Step 16Completed 5:30:59 PM

Record satellites number and HTOP number

Write down Satellites Number and HTOP Number.

Record both MissionPlanner readings before completing this step.

Drone Positioning

Complete each item in sequence.

Step 17Completed 5:31:02 PM

Place the drone in the center of the launch pad

Launch

Complete each item in sequence.

Step 18Completed 5:31:04 PM

Launch Drone

Post-Flight Check

Complete each item in sequence.

Step 19Completed 5:38:06 PM

Record post-flight battery voltage

  • Record the battery number and the measured post-flight battery voltage.

Post-flight battery voltage has been recorded.

Charger Check

Complete each item in sequence.

Step 20Completed 5:39:56 PMOptional

Record charger voltage

Optional: record the charger voltage. You can leave this blank and still complete the step.

Optional — you can complete this step without recording a charger voltage.