Session Archive

All preflight logs

Review every saved preflight session, including checklist progress, timestamps, and recorded field measurements.

Back to dashboard

Total Logs

105

In Progress

3

Completed

102

Saved Logs

Select any saved session to inspect its recorded checklist.

Drone 004 - 小柯

Checklist completeFull Preflight

Started Jul 22, 2026, 4:50 PM

Updated Jul 22, 2026, 5:14 PM

Checklist Progress

24/24

100% complete

Checklist Progress24/24

Last Completed Step

Record charger voltage

5:14:20 PM

Session Status

Completed

Completed Jul 22, 2026, 5:14 PM

Battery Check

Archived checklist entries for this SOP section.

Step 1Completed 4:50:57 PM

Measure and record battery voltage

  • Record the battery number and the measured battery voltage.

Acceptable range: VMeasured > 49.6

Battery voltage is within the acceptable range.

Battery Placement

Archived checklist entries for this SOP section.

Step 2Completed 4:51:00 PM

Align the battery to the white line

Step 3Completed 4:55:04 PM

Secure the velcro straps

Step 4Completed 4:55:06 PM

Wiggle-test the battery

The battery should not move once strapped in.

Battery Cover

Archived checklist entries for this SOP section.

Step 5Completed 4:55:07 PM

Tape down the battery cover with flight tape

Remote ID

Archived checklist entries for this SOP section.

Step 6Completed 4:55:09 PM

Turn on the Remote ID module

Flip the red switch on the Remote ID module to power it on.

Ground Control Center & Drone Connectivity

Archived checklist entries for this SOP section.

Step 7Completed 4:55:10 PM

Confirm airspeed sensor data in MissionPlanner

Blow on the airspeed sensor and verify the reading is reflected in MissionPlanner.

Hardware Check

Archived checklist entries for this SOP section.

Step 8Completed 4:55:11 PM

Verify the VTOL motor does not budge

Grab the VTOL motor with your palm and lightly try shifting it.

Step 9Completed 4:56:24 PM

Measure rear motor temperature

Acceptable range: TBD

Step 10Completed 4:56:26 PM

Measure quad motor temperatures

Acceptable range: TBD

Step 11Completed 4:56:27 PM

Inspect propellers for cracks or cuts

Step 12Completed 4:56:29 PM

Inspect the servo and rod for secure attachment

Step 13Completed 4:56:33 PM

Manually move the rudder to confirm servo engagement

Remote Controlled Pre-Check

Archived checklist entries for this SOP section.

Step 14Completed 5:01:53 PM

Run the same-direction rudder test

Flip the red button toward the pilot to enter airplane mode, then use the left joystick so both rudders move in the same direction.

  • Repeat the motion 10x.
  • Observe rudder smoothness and speed on every pass.
Step 15Completed 5:04:34 PM

Listen for unusual sounds during the same-direction test

Step 16Completed 5:05:46 PM

Run the opposite-direction rudder test

Use the right joystick so the rudders move in opposite directions.

  • Repeat the motion 10x.
  • Observe rudder smoothness and speed on every pass.
Step 17Completed 5:06:39 PM

Listen for unusual sounds during the opposite-direction test

MissionPlanner Connectivity Check

Archived checklist entries for this SOP section.

Step 18Completed 5:06:59 PM

Record satellites number and HTOP number

Write down Satellites Number and HTOP Number.

Saved MissionPlanner readings from this preflight session.

Drone Positioning

Archived checklist entries for this SOP section.

Step 19Completed 5:07:03 PM

Place the drone in the center of the launch pad

Launch

Archived checklist entries for this SOP section.

Step 20Completed 5:07:06 PM

Launch Drone

Post-Flight Check

Archived checklist entries for this SOP section.

Step 21Completed 5:12:57 PM

Record post-flight battery voltage

  • Record the battery number and the measured post-flight battery voltage.

Post-flight battery voltage was recorded for this session.

Step 22Completed 5:13:07 PM

Record post-flight rear motor temperature

Step 23Completed 5:13:45 PM

Record post-flight quad motor temperatures

Charger Check

Archived checklist entries for this SOP section.

Step 24Completed 5:14:20 PMOptional

Record charger voltage

Optional: record the charger voltage. You can leave this blank and still complete the step.